Press "Enter" to skip to content

How much wallpaper border do I need?

To determine how much border, your project requires:

  1. Measure the width of each wall where you would like to apply the border and add them all together (“Combined Width”)
  2. Divide the combined width by width of the spool selected, in most cases this will be 15.
  3. Round up to the nearest whole number.

How long is a roll of wallpaper border?

about fifteen feet

How many square feet does a double roll of wallpaper cover?

61 square feet

What comes first flooring or baseboard?

Baseboards are often installed before flooring, although it depends on the type of flooring being used. It is necessary for carpeting to have the trim in place, allowing the edges to be tucked under and out of sight. However, for hardwood or laminate, it is easier to install the trim after.

What’s the difference between quarter round and shoe molding?

Shoe molding is much the same as quarter round, having the same 90° angle on the backside but instead of being a perfect quarter radius, its profile is a bit more squat. Using shoe molding gives the floor installer more latitude in their end cuts and also allows the trim carpenter to hide un-level floors.

What is another name for quarter round?

Alternate Synonyms for “quarter round”: ovolo; thumb; molding; moulding.

What size nail do I use for shoe molding?

If you’re wondering “Which nails should I use for shoe molding?” the answer is 2″ brad nails for the nail gun. Try to find smaller finishing nails for your hammer so they’re not so noticeable on the shoe molding.

What are 18 gauge nails used for?

18-gauge brad nailers shoot a thin nail between 3/8” to 2” depending on the model. They leave a smaller hole thanks to their small head and so are less likely to split thinner wood. They’re the ideal nailer for attaching casing to window and door jambs because they’re less likely to blow out the connections.

Can I use 18 gauge nails for trim?

The 18 gauge brad nailer works well for thin trims, base cap, and shoe molding; but not recommended for thick baseboards. In short, the choice between a finish nailer and a brad nailer depends on the thickness of the baseboard or trim. Go for a pneumatic nailer since they cost less and are powerful.

Can you use a brad nailer for trim?

Brad Nailer Pros Perfect for attaching delicate trims and moldings. The 18-gauge nail usually does not split the trim. It can also be used on smaller baseboards and plywood up to ½-inch.

What kind of nail gun do I need for trim?

16-gauge nails are the most versatile size, so a 16-gauge nail gun is a great option if you need it for many different projects. 15-gauge nails are most often used for installing thick trim. 18-gauge and higher-gauge nail guns are best used for fine detail work, furniture repair and thin trim work.

Can you put up trim without a nail gun?

Your local big-box hardware store carries molding in all different styles, and they’ll cut it down for you to the exact sizes you need. Installing it is as simple as buying a box of itty-bitty finishing nails and hammering in the molding. Seriously, you do not even need a nail gun.

How long should nails be for framing?

3 1/2 inches

What size screws should I use for framing?

9 and 10 screws are the most common for studs, and driver tips should correspond with those screw sizes. For example, a standard No. 2 Phillips tip is appropriate for No. 9 and some No.

Are joist hangers stronger than screws?

According to Simpson, using their structural screws designed to work specifically with their joist hangers will result in a stronger connection than using standard nails. You’ll need both the 1 ½” screws and the 3” screws.

Can you use 16 gauge nails for framing?

Common nails are made with a heavier-gauge wire, typically about 5/32” thick. They’re generally used in house framing, where strength is important. Box nails have thinner-gauge shanks—about 1/16” which are best for fastening nonstructural things like trim, shingles, and siding….Choosing the Right Nail for the Job.

Gauge Common
16 0.06
18 0.05
23 0.03

Can I use Brad Nailer on 2×4?

It would depend on what you are using the brads for. If you want to shoot the mdf down to a 2×4 ledger you should be fine. You surely wouldn’t want a framing nail or screw hear sticking out of the face of a shelf.

Can I use a framing nailer for trim?

As the name suggests, these nail guns are used for the finishing touches. The scope of doable works includes trimming, interior molding, paneling, baseboards. It is also the tool of choice for furniture assembly. Generally lighter by itself, the gun also shoots lighter nails.